piaqua

PiAqua

Raspberry Pi aquarium controller

Capabilities

• advanced scheduler and manual switches for 6 x 220V outputs (filter, lights, etc.)
• water and room temperature sensors
• www server with display / control / setup interface

Hardware

• Raspberry Pi Zero W
• SD card (4GB recommended)
• power supply 2A
• DS18B20 waterproof x2 (or more) - 1-Wire Digital Temperature Sensor
• 4,7kΩ resistor for 1-wire sensors
• SSR RELAY - OMRON G3MB-202P - 8 channels module (6 channels used)
• momentary push-button switch x3

Installation

Download latest Raspbian Lite from:
https://www.raspberrypi.org/downloads/raspbian/

Install image to the SD card

# on linux run `lsblk` to find device file eg. `/dev/sdX`
$ umount /dev/sdX*
$ sudo dd bs=4M if=xxx.img of=/dev/sdX status=progress conv=fsync

Setup WiFi

# mount sd-card (reinsert it)
$ cd /boot
$ vim wpa_supplicant.conf

ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1
country=«your_ISO-3166-1_two-letter_country_code»

network={
    ssid="«your_SSID»"
    psk="«your_PSK»"
    key_mgmt=WPA-PSK
}


# enable ssh access
$ touch ssh

# unmount and insert sd-card into Raspberry Pi

Configure system

# insert sd-card to raspberry pi and boot
$ ssh pi@«ip-addr»
# password: raspberry

$ sudo raspi-config
# - expand filesystem
# - change hostname
# - change password
# - set timezone
# - enable 1-Wire interface (for temperature sensors)
# - disable serial interface (if not needed)
# - reboot

$ sudo rpi-update
$ sudo apt update
$ sudo apt dist-upgrade

# edit boot options
$ sudo vi /boot/config.txt
# disable bluetooth (if not needed) - append:
dtoverlay=disable-bt
# and disable splash:
disable_splash=1
# and disable boot delay
boot_delay=0
# and disable audio (if not needed):
# comment out: dtparam=audio=on

# disable unused services
$ sudo systemctl disable hciuart
$ sudo systemctl disable avahi-daemon
$ sudo systemctl disable triggerhappy

# disable swap
$ sudo systemctl disable dphys-swapfile

# reduce cron tasks
$ sudo apt purge man-db

# ramdisk mounts
$ sudo vi /etc/fstab
# and append:
tmpfs /tmp tmpfs defaults,noatime,nosuid,size=32m 0 0
tmpfs /var/tmp tmpfs defaults,noatime,nosuid,size=32m 0 0
tmpfs /var/log tmpfs defaults,noatime,nosuid,size=32m 0 0

# fix wifi disconnection issue
$ sudo vi /etc/rc.local
# and append before exit:
iw wlan0 set power_save off

$ sudo reboot

Enable internet access

• create dns name, eg:
  https://www.duckdns.org
• add cron entry to update IP (follow the site instructions)
• setup port forwarding in your router:

WEB interface is accessible under http://«dnsname»/.
If your router doesn't support NAT loopback (hairpinning), then inside LAN the interface is accessible only under http://«ip_address»:8080/.

Enable easy ssh access (under linux)

# append ssh config lines
$ sudo vim /etc/ssh/ssh_config
Host piaqua
    Hostname «ip_address»
    User pi
# copy ssh keys to log without password
$ ssh-copy-id piaqua

Build and deploy an application

# create user etc
$ scripts/prepare_env.sh

# create systemd service
$ scripts/deploy_service.sh

# upload configs
$ scripts/deploy_configs.sh

# adjust sensor ids and pin numbers in:
# /opt/aqua/configs/hardware.yml

# change web api credentials in:
# /opt/aqua/configs/server.yml

# upload www files
$ scripts/deploy_www.sh

# build an app
$ ./docker-build

# and deploy it
$ scripts/deploy_app.sh

Debugging

# check service status
$ systemctl status aqua
# view logs
$ journalctl -u aqua